Lansete CUSTOM

[semlecangheorghe]

Si daca nu ''citezi'' se rezolva cu ordonanta de urgenta.. ..

[andriipopa75]

Da, deobicei unul este mai pronuntat.
In cazul tau, ia in considerare pe care doresti sau chiar nici unul. Mitul spine-ului e depasit deja in zilele noastre si a fost demontat de teste concrete....
Majoritatea builderilor consrtruiesc pe curbura care deobicei nu coincide cu spine-ul.

Dupa afirmatia asta, singura ta scuza este doar daca construiesti bete light pt pesti < 500g, altfel cred ca nu ai inteles tehnica construirii unei lansete.

Cand lanseta nu este pe sir , se observa urmatoarele:
1. varful se balangane sub forma de triunghi, nu sus-jos;
2. la lansetele din 2 bucati, au tendinta sa se rasuceasca varful sau, mai rau, sa se demufeze dupa mai multe lanseuri - risc de rupere;
3. lansetele se inmoaie mai repede in timp, din cauza tendintei naturale de rasucire a fibrelor de carbon ;
4. la lansetele folosite cu greutati mari - de ex. de crap, prin montarea pe sir, in afara de cresterea lanseului scade foarte mult riscul de rupere, mai ales pt. motivul.2 ;
5. sirul unei lansete iti permite sa o gandesti pentru lanseu (cast) sau pentru finete in drill (spinning);

Daca blankul are o curbura vizibila, pentru aspect poti monta inelele pe curbura pentru a masca acest lucru, ignorand sirul blankului, dar pt medium, heavy e de preferat sa respecti sirul .

[ULK]

Teoretic asa e ...practic,fara baza reala de adevar cu exemple concrete.

[lau_bau]

Teoretic asa e ...practic,fara baza reala de adevar cu exemple concrete.

Tu te auzi ce vorbesti ???

[ULK]

Defapt nici teoretic ...din mai multe considerente.

[ULK]

O parere bazata pe zeci de teste si peste 35 de ani de rodbuiding( lansete de toate puterile)

Tom Kirkman scria in 2008 si sustine in continuare:

There has never been any evidence given that offers proof or good reason for mounting guides on the spine or opposite the spine. The whole idea that it was a good idea came from a book written in the early 1970's and which other authors then picked up on. None offered any reason for doing this other than that if you flexed a naked blank by hand (which never happens while fishing - our rods have guides on them which act as small lever arms and overcome "spine") the blank would roll to a certain location. The authors stated that utilizing the spine in the manner they recommended would prevent rod twist while fishing and create a more accurate fishing rod. Both statements have been very much disproven in actual mechanical tests over the years. For the most part, everything written about the importantance of rod spine in the various texts out there has always been based on opinion, not tests or facts. But if you repeat something often enough and long enough, it tends to become "fact." It's a hard myth for many to let go of, but it will die in the next few years. At least one publication actually somewhat recanted on their 20+ year stance on the importance of spine after our test results were printed in a very early issue of RodMaker. They too, then decided that spine has nothing to do with preventing rod twist.

Guide location has everything to do with rod twist, spine has nothing to do with it. For best accuracy, you need the straightest axis in line with your casting plane, only problem being that most of us don't always cast on the exact same plane each time. But you don't want any natural curvature being so far off line from the normal casting plane that the rod tip will travel in an arc (twist around a central axis is fine).

If you do choose to build on the spine, however, you won't hurt a thing. If it makes you feel good - go ahead and do it. That's precisely because it just doesn't matter. The one thing you never want a new builder to worry over is rod spine. Far too many shy away from building a rod because they're afraid or have been told that if they don't get this spine thing correct, their rods will twist, explode, cast to the left, etc. But none of that is the actual case. Try not to worry over it too much - it really doesn't matter.

[ULK]

Se referea la Dale Clemens si cartea lui "Advanced custom rod building".

[ULK]

O poza din revista RodMaker dintr-un articol cu teste concrete bazate pe cifre exacte, da un raspuns la mai multe "dece"-uri din "teoria spine"-ului.

[semlecangheorghe]

Daca tii blankul pe spin si varful fuge stinga ori dreapta??Ce faci, montezi inele pe spin si varful o ia dupa colt??Naspa..

[andriipopa75]

Daca blankul are o curbura vizibila, pentru aspect poti monta inelele pe curbura pentru a masca acest lucru, ignorand sirul blankului, dar pt medium, heavy e de preferat sa respecti sirul .